Vacuum vs. Air: When a Loop Capacitor Earns Its Keep
Vacuum vs. Air: When a Loop Capacitor Earns Its Keep
A good air-spaced capacitor can be an excellent choice for a small transmitting loop. A vacuum variable earns its price when it solves a real voltage, current, heat or packaging problem. Moving the loop from the car trunk to the garden changes the practical priorities—but it does not automatically make vacuum the winner.
Start with a good air capacitor, not a straw man
The question behind this article is a useful follow-up to our discussion of small-loop efficiency: when does a vacuum variable justify the extra money—and does the answer change for a loop that stays in the garden instead of traveling in the trunk?
If the existing air capacitor already handles the circulating current, withstands the RF voltage and contributes little loss, replacing it with a vacuum unit may produce only a small increase in radiated power. The replacement may still be worthwhile for cooling, tuning or construction reasons. Those are real benefits, but they should be named accurately.
We are comparing a vacuum variable with a proper transmitting capacitor: adequate spacing, substantial conductors, sound connections, suitable supports and a low-loss RF current path. An elderly broadcast-radio tuning capacitor with an unsuitable rotor contact is a different comparison.
Buy the improvement your loop needs. If the limitation is a hot capacitor, inadequate working voltage or an impractical air-capacitor enclosure, a suitable vacuum unit can be money well spent. If the limitation is a small conductor, poor joints or a lossy installation, changing the dielectric does not remove it.
The capacitor is doing more than tuning
In an electrically small transmitting loop, the conductor and tuning capacitor form a resonator. Energy repeatedly moves between the magnetic field around the conductor and the electric field between the capacitor electrodes. The transmitter supplies the energy that leaves as radiation and heat.
That circulating energy is why the capacitor can carry tens of amperes and develop several thousand volts even when the transmitter supplies only modest power. The current in the loop is not the current in the 50-ohm feed cable. Likewise, the voltage across the capacitor is not the voltage at the radio socket.
Resistance turns some of that current into heat. In a capacitor we represent the loss as equivalent series resistance, or ESR: a small resistance that would dissipate the same power at the operating frequency and capacitance. It includes more than the material between the plates. Electrodes, terminals, joints and the moving-electrode connection matter.
Radiation resistance represents the power that actually leaves as radio waves. It is not a physical resistor that gets hot. For a very small loop it can be only a few thousandths of an ohm, so seemingly tiny unwanted resistances can become important.
Air and vacuum are both very low-loss dielectric media. The useful comparison is between two complete components in the actual circuit. A vacuum capacitor is not a zero-resistance component, and “air-spaced” does not mean “lossy.”
A butterfly changes the current-path argument
A conventional variable capacitor may connect its moving plates through a wiping contact. Whether that is acceptable depends on the contact design and the current. A contact intended for a receiver is not automatically suitable for the resonant current of a transmitting loop.
A butterfly capacitor, connected between its two stationary plate sets, offers another route. RF crosses the first capacitance, travels through the common moving conductor and crosses the second capacitance. The principal RF path does not need a sliding electrical connection to the rotor. A suitably constructed and connected split-stator capacitor can use the same series principle.
This is established capacitor engineering: Cardwell describes the arrangement in its Type BFC documentation. That page demonstrates the topology; it is not a recommendation of that particular part for the voltage in our example below.
Two sections do not mean twice the capacitance
Two equal sections of 400 pF in series give 200 pF between the outside terminals. Both carry the same series current; their losses add. In an ideal symmetric arrangement each section takes half the terminal voltage. Real construction, stray capacitance and external clearances determine the safe working rating—do not simply double a catalog voltage.
The moving conductor still carries RF, and a nominal midpoint is not a promise of a touch-safe shaft.
Read the ratings before reading the price
A capacitor does not have a useful universal “100 W” or “1 kW” loop rating. Its required current and voltage depend on loop geometry, frequency, loss, tuning capacitance and accepted power. Operating mode adds a thermal requirement.
Swipe or scroll sideways to compare all columns.
| Check | What the loop needs | Common purchasing mistake |
|---|---|---|
| Capacitance range | Enough maximum capacitance for the lowest frequency, and sufficiently low minimum capacitance for the highest, including the installation’s stray capacitance. | Buying by the maximum pF value alone. |
| RF working voltage | A specified permissible peak voltage with operating margin at the actual setting. | Treating a breakdown test or short-duration withstand value as a continuous operating rating. |
| RF current | RMS current capability at the required frequency, capacitance and cooling conditions. | Using the largest ampere number from a different operating point. |
| Loss | ESR or component Q at the relevant operating point, including the connections. | Assuming every vacuum unit has less loss than every air unit. |
| Mechanics | Usable tuning resolution, safe drive travel, supported terminals and repeatable operation. | Ignoring backlash, mounting loads and the cost of the actuator. |
Peak and RMS are different. Peak describes the highest instantaneous RF voltage. RMS is the effective current used for heating calculations. For a sine wave, peak voltage is √2 times RMS voltage. A specification must say which it means.
For a concrete example of rating discipline, the manufacturer’s Comet CVUN-250AC/15-JHJA-Z data sheet lists 25–250 pF, 15 kV test but 9 kV working, and a 94 A RMS headline tied to 13.56 MHz and specified conduction cooling. The curves and cooling instructions are part of the specification. That does not establish a 94 A rating at every HF frequency or inside any enclosure.
For SSB, check peak RF voltage at the intended peak envelope power. Heating follows the time average of current squared. Sustained carrier and digital transmissions can therefore be much more demanding thermally than intermittent speech, even when the peak-power number is lower. CW also has a key-down duty cycle; there is no single conversion factor covering every operator and mode.
A loop in the garden changes the priorities
Identical loops at the same site and power obey the same circuit laws whether you pack them away afterward or leave them standing. What changes is the design freedom and the exposure to the environment.
Swipe or scroll sideways to compare both installations.
| Portable: back into the trunk | Permanent: out in the garden |
|---|---|
| Transport size, weight, repeated assembly and protection from knocks matter. | A larger enclosure, substantial supports and a more elaborate drive may be practical. |
| Removable loop joints and connectors must remain low loss after repeated use. | A rigid conductor and durable, low-resistance joints become easier to implement. |
| Short operating sessions may reduce average heating, but do not remove the peak-voltage requirement. | Long transmissions, unattended weather exposure and hot enclosures deserve deliberate thermal design. |
| A good air capacitor can keep construction straightforward when its size is acceptable. | Extra space can accommodate an excellent air capacitor. Vacuum can help when the required current and voltage must fit into a smaller protected assembly. |
My first question for a fixed garden loop would be whether the loop itself can improve. A larger loop area where space permits, a suitable larger conductor and better joints may buy more than replacing an already good capacitor. Recalculate the tuning range and operating stress after changing the geometry. Making a loop larger also eventually takes it outside the simple electrically small-loop model.
The location matters independently of the capacitor. A nearby metal fence, building or wet vegetation can change tuning, introduce loss or alter the radiation pattern. A portable loop tried in an open field and a fixed loop beside a shed are not a controlled capacitor comparison. A vacuum upgrade cannot cancel the influence of the site.
The garden adds rain, condensation, dust, insects, corrosion and wind. Protect air-capacitor plates and their supports from contamination. For either type, plan drainage or condensation control, suitable materials, electrical clearances and maintenance access. An enclosure that keeps rain out can still become humid inside or trap heat.
A vacuum capacitor protects its internal electrode gap from the outside atmosphere. The terminals, external insulating surface, connections and motor remain outside that vacuum. The distinction follows directly from the construction shown in the Jennings manufacturer catalog: a sealed capacitor is not a weatherproof complete antenna assembly.
Mechanical support matters too. Support the capacitor and drive using the component’s intended fixing points, follow its mounting instructions and allow for thermal movement. Do not use the capacitor as the structural member that absorbs movement of the antenna, or force misaligned terminals together with the mounting bolts.
A motor and reduction drive can make a narrow resonance much easier to tune. Provide suitable travel limits and avoid forcing the capacitor against its stops. Vacuum variables have moving bellows and finite mechanical life; the Jennings catalog discusses the dependence on stroke and cycling. An unknown surplus unit with a large voltage marking still needs an identifiable specification and a known usable condition.
A garden installation must also keep people and pets away from energized parts. Use remote tuning and an appropriate enclosure; do not reach in to adjust live plates. Assess RF exposure for the actual installation. A weather cover or a remote motor does not by itself establish a safe distance.
A small signal improvement can be a large thermal improvement
Consider a deliberately simplified example at 7 MHz. Both capacitors tune the same loop to resonance at an effective 200 pF. We keep the geometry and all other losses unchanged, adjust the feed match as needed, and deliver 100 W of accepted power to the resonator. Feedline and matching losses are excluded from this example.
Assume a radiation resistance of 6 milliohms and other equivalent series losses of 34 milliohms. A milliohm is one thousandth of an ohm. Now compare an air capacitor with 4 milliohms ESR against a vacuum capacitor with 1 milliohm ESR.
These are hypothetical component values, not measurements or typical specifications for either technology. The example isolates what a reduction in capacitor loss does. A real selection needs ESR and ratings for the actual parts and operating point.
| Calculated quantity | Air: 4 mΩ ESR | Vacuum: 1 mΩ ESR |
|---|---|---|
| Total equivalent series resistance | 44 mΩ | 41 mΩ |
| Radiation efficiency | 13.64% | 14.63% |
| Radiated power | 13.64 W | 14.63 W |
| Loop and capacitor current | 47.67 A RMS | 49.39 A RMS |
| Heat generated in the capacitor | 9.09 W | 2.44 W |
| Capacitor voltage, RMS | 5.42 kV | 5.61 kV |
| Capacitor voltage, peak | 7.66 kV | 7.94 kV |
The radiated-power improvement is approximately 0.31 dB, assuming the radiation pattern remains unchanged. That is a modest signal increase. Yet capacitor heating falls by about 73%. For a component inside a small enclosure during a long transmission, that may be the more valuable improvement.
Notice the other result: current and capacitor voltage rise after the loss is reduced. At the same accepted power, the more efficient resonator circulates more current. An upgrade can expose the next voltage or current limitation.
The vacuum capacitor has not removed the other 34 milliohms of loss. In this example, even an impossible zero-loss capacitor would raise efficiency only to 15%, a gain of about 0.41 dB over the assumed air version. That gives a useful ceiling on what any capacitor-only upgrade can achieve here.
Nor should the heating reduction be read as an automatic temperature or lifetime guarantee. The two components can have different heat paths and allowable temperatures. Fewer watts dissipated is valuable; the final temperature still depends on the installation.
The engineering behind the example
For readers who want to check the numbers, the model is a single series-resonant loop with approximately uniform circulating current. All resistances below are referred to that same current. The accepted power supplies radiation and the modeled losses.
η = Rradiation / Rtotal
IRMS = √(Paccepted / Rtotal)
The symbol η is radiation efficiency as a fraction. Multiplying by 100 gives percent. Capacitor heat is:
Capacitive reactance describes the relationship between sinusoidal current and voltage. With frequency f in hertz and capacitance C in farads:
VC,RMS ≈ IRMS × XC
VC,peak ≈ √2 × VC,RMS
At 7 MHz and 200 pF, XC is approximately 113.68 ohms. The peak-voltage equation assumes sinusoidal steady-state operation; the capacitor voltage approximation neglects the tiny ESR contribution. It does not account for every transient, parasitic resonance or distributed effect in a real loop.
The power ratio gives the relative efficiency gain:
Δ = 10 log10(44 / 41) ≈ 0.31 dB
With fixed resistances, doubling accepted power doubles the heat and multiplies current and voltage by √2. Real resistance can change with temperature, which is one reason to check thermal behavior instead of extrapolating indefinitely.
Minimum capacitance can decide the purchase
A large maximum capacitance is useful only if the low end is also suitable. For a simple resonator with fixed effective inductance L:
Keeping the same inductance, 200 pF at 7 MHz becomes 50 pF at 14 MHz and 12.5 pF at 28 MHz. These are total equivalent tuning capacitances. A variable whose minimum is 25 pF cannot reach the last value in this simple arrangement, even before adding stray capacitance.
That is a tuning-range calculation, not a promise that one physical loop remains electrically small or performs well across all three frequencies. Leads, supports, an enclosure and nearby objects change the circuit. Check the assembled antenna, including the motor and wiring—not just the loose capacitor on a capacitance meter.
Also check adjustment resolution where you need it. A broad range on paper is little comfort if a tiny shaft movement jumps across the whole useful resonance. Gear reduction helps resolution; excessive backlash makes returning to a setting frustrating. Both air and vacuum designs can be motorized well.
Q is useful, but it is not an efficiency certificate
Q describes stored energy relative to energy lost per RF cycle. A capacitor’s component Q, the loop resonator’s Q and the Q inferred from a coupled antenna measurement are different quantities.
For a low-loss capacitor in the series model, QC ≈ XC/ESR. Our assumed values imply component Q values of roughly 28,400 and 113,700. Those deliberately declared assumptions are not generic air-versus-vacuum specifications.
A lower-loss capacitor can make an otherwise unchanged loop’s resonance narrower. That often means more frequent retuning, rather than a defect. Conversely, extra loss can broaden a resonance while turning more transmitter power into heat.
But you cannot reverse that observation into “narrow bandwidth proves good efficiency.” Feed coupling, radiation, surrounding objects and measurement loading also influence the response. A low standing-wave ratio—SWR—only says the feed presents a good match at the measurement point. A dummy load can do that very well.
Check the complete assembly before declaring a winner
Use short, substantial RF connections and appropriate terminal hardware. A thin lead or poor joint can give back the loss you paid to remove. Keep the manufacturer’s required clearances and mounting arrangements; the shortest connection is not automatically a safe connection.
For an A/B comparison, hold the loop geometry, location, surroundings and operating frequency constant. Retune and rematch each version. Compare at the same accepted power at a declared reference point, not merely the same transmitter setting. Account for feedline and matching changes before attributing the result to the capacitor.
A vector network analyzer, or VNA, is useful at low power for locating resonance, checking tuning range and observing repeatability. It does not, from a one-port SWR trace alone, measure the capacitor’s milliohm ESR or the antenna’s radiation efficiency. Measuring such low RF loss needs a suitable resonant fixture, calibration and control of fixture, connection and coupling losses.
Then check operation under representative duty and thermal conditions, with suitable remote observation and within the verified ratings. Look for heating, resonance drift and inconsistent tuning. Keep hands and ordinary test leads away from the energized high-voltage region; attaching a probe can itself alter the resonance and stress. Arcing is a fault to stop and investigate, not a normal power-rating test.
If the claimed improvement is radiated signal, make a controlled field comparison as well. Keep receiving position and geometry fixed, avoid receiver compression and allow for propagation changes. An uncontrolled on-air report is not convincing evidence of a 0.3 dB capacitor improvement. Reduced heating may be much easier to demonstrate reliably.
Where I would spend the money
For a portable loop at modest power, I would keep a sound air-spaced transmitting capacitor if it meets the actual stress, loss and tuning requirements and travels well. I would improve poor joints before buying an expensive replacement.
For a permanent garden loop, I would use the extra freedom first: better loop geometry where possible, a rigid conductor, dependable connections, a protective enclosure and comfortable remote tuning. A larger, good air capacitor may be entirely practical there.
I would choose vacuum when a specific part provides the needed current and peak-voltage margin, reduces troublesome capacitor heating, or makes the required performance fit into a practical assembly. At higher circulating energy and sustained duty, those benefits become increasingly valuable—but there is no universal transmitter-power threshold.
A vacuum variable earns its keep by solving a measured or calculated limitation. A good air capacitor earns its keep by already meeting the requirement. The garden changes which solution is convenient and durable. It does not award free decibels.
Mini-FAQ
- Is a vacuum variable always more efficient than an air capacitor? No. Compare actual RF loss at the required capacitance and frequency, including the connections. A good air capacitor can contribute very little to the complete loop’s losses.
- At what transmitter power should I switch to vacuum? There is no universal threshold. Loop current, capacitor peak voltage, duty cycle, cooling and the specific component ratings determine suitability.
- Can a capacitor upgrade help even if the signal increase is tiny? Yes. In the hypothetical example, the radiated-power gain is about 0.31 dB while capacitor heating falls from 9.09 W to 2.44 W. Actual temperature also depends on cooling.
- Does a butterfly capacitor eliminate all capacitor loss? No. Its series arrangement can avoid a sliding rotor contact in the principal RF path, but electrode, conductor, terminal and connection losses remain.
- Does a vacuum capacitor make a garden loop weatherproof? No. The internal electrode gap is sealed; the external insulation, connections, supports and tuning mechanism still require suitable environmental protection.
- Will a lower-loss capacitor make tuning easier? Not necessarily. Lower total loss can narrow the resonance and raise circulating current and voltage. A well-designed reduction drive and remote tuning can make that narrow resonance easier to manage.
Found this useful? Support my writing and experiments: Buy me a coffee.